4Runner, FJ Cruiser, GX 460 470 Heavy Duty Offset Non-Adjustable Rear Link Set – POLYURETHANE BUSHINGS
$797.45
KDSS COMPATIBLE (4Runner & GX 460 / 470)
BENEFITS OF NON-ADJUSTABLE LINKS OVER STOCK OR ADJUSTABLE LINKS
STRENGTH – made from stronger materials – won’t bend like factory links.
INCREASED TRAVEL – our offset links will allow for more drop with long travel setups before binding.
ALIGNMENT – returns alignment close to stock position after a lift.
LOW MAINTENANCE – no jam nuts or threaded rod ends that are going to loosen or freeze.
DEPENDABILITY – they’re fully welded so they won’t pull apart on the trail and leave you stranded.
RIDE QUALITY – stiffer than rubber bushings but softer than heim joints. Minimal noise compared to heims or Johnny Joints.
EASILY FIXED – if the Energy Suspension bushings go bad they can easily be popped out and replaced.
Made in the USA!
**Not sure which links to get!?**
Answer a few questions from our Rear Link Guide
**LEAD TIME: 3-4 months
If you have a Toyota FJ Cruiser, 4Runner, or Lexus GX 460 & GX 470 and are looking for a heavy duty replacement for your factory control arms or want to fine tune your suspension, this rear link set will meet your needs. All of the links in this set are slightly longer than stock to account for small lifts and are also welded at both ends for maximum strength and durability. These will not rip out on the trail and leave you hanging like some of the adjustable options on the market. They’re also very easy to maintain and much cheaper to fix if/when a bushing becomes worn out. For those that live in the “rustbelt”, you know how bad that salt eats away at parts. Johnny Joints and heim joints do NOT last long around here.
HEAVY DUTY LOWER LINKS
Our heavy duty lower links are offset at the axle end to help prevent binding at full articulation and gives you a smoother sliding surface when on the rocks.
Our more budget friendly Energy Suspension polyurethane bushing ends are definitely our most popular. They’re a little easier on the wallet, but still add the same protection as our other higher performing links. As mentioned before, they’re also very easy and cheap to replace when the time comes.
All Resz Fab non-adjustable lower links are made from 1.5″ x .375″ DOM U.S. made steel tubing with grease fittings at each end(with the exception of the Duroflex Joint). Welded to the middle of each tube is an e-brake bracket with a welded M8 nut on the back that uses the existing bolt.
OFFSET UPPER LINKS
Whether you’re looking for a replacement for your worn out factory links, want to get your pinion angle closer to factory specs after a lift, or have issues with your other aftermarket links hitting your gas tank from a long travel rear suspension, these non-adjustable offset upper links will meet your needs. All non-adjustable links are made roughly 3/16″ longer to account for a 3″ lift. If you’d like factory length, please specify in the notes.
Resz Fab non-adjustable upper links are made from 1.25″ x .120″ DOM U.S. made steel tubing.
EXTENDED PANHARD BAR
The RESZ Fabrication panhard bar is perfect for those looking to center their axle after installing a small lift on their FJ, 4Runner, or Lexus GX.
These non-adjustable panhard bars are made from 1.25″ x .313″ DOM U.S. made steel tubing. The polyurethane housings on both ends are made from 2.25″ x .250″ DOM tubing with threaded holes to accept standard 1/4″ grease fittings(included).
All of the links in this set come with a limited lifetime warranty. This covers the tubes and polyurethane bushing housings. It does not cover the bushings or zerks(grease fittings)
FITMENT
2007 + Toyota FJ Cruiser
2003 + Toyota 4Runner
2003 – 2009 Lexus GX470
2010 + Lexus GX460
These are compatible with or without KDSS
Related products
4Runner (4th-5th gen)
4Runner / FJ Cruiser Heavy Duty Offset Non-Adjustable Rear Link Set – DUROFLEX JOINTS
FJ Cruiser
FJ Cruiser
